Hot tub hire in Durham, Gateshead, Newcastle, Northumberland & Sunderland

Book Online

Hot Tub Instructions

PLEASE READ


Click here for your water treatment guide

  1. Fill the hot tub with hot or cold water up to the minimum level which can take up to 2 hours depending on water pressure.
    (a) Cold water fill, wait till the water level has passed the inlet pipes to press the heat button you, it can take up to 24 hours to heat depending on outside temperature.
    (b) Hot water fill, you need to balance the temperature so it does not go to hot to quick and you will also need tap adapters for your hose pipe to attach.
  2. You will need to press the unlock button if the red light is on the lock symbol before pressing any other buttons.
  3. Make sure you check the temperature is set to 40 degrees celcious.
  4. Make sure the heat activation stays on for the full hire.
  5. Click here for your water treatment guide
  6. Everyone needs a shower before and after using the hot tub, you need to keep the water clean as possible to avoid any error codes.
  7. Clean the Filter daily after using the hot tub, unscrew the grey filter housing from inside the hot tub, take the filter out give it a good clean under the tap, put it all back together and turn the power on, press the reset on the rcd and power on the console.
  8. Keep your feet clean when entering the hot tub.
  9. Thermostat reset, If after 2-3 hours you think the temperature has not moved you will need to do a thermostat reset, turn the power off by the plug, on the side of the pump half way up next to a yellow sticker you will see a little black/gray button press this in for 3 seconds, turn the power back on, press the reset button on the rcd, press the power on button on the console and remember to press the heat button.
  10. Error 2 means you have a dirty filter, you will need to turn the power off, unscrew the grey filter housing from inside the hot tub, take the filter out give it a good deep clean under the tap or hose pipe, put it all back together and turn the power on, press the reset on the rcd and power on the console.
    If error 2 continues, this means the water is too dirty or the filter has not been cleaned properly.
  11. Temperature will not stay at 40 when using the hot tub for long periods of time. If the temperature drops too low you will need to put the lid back on and let it heat up. It can take 1-2 hours for every degree depending on outside temperature.
  12. Power Off, If the power has tripped or been turned off, you will need make sure the switch is on and press the reset button on the RCD, you will also need to press the power button till it turns green on the control panel, make sure the heat activation is on red or green.
  13. (FINISHED) Hot tub collection, To empty the hot tub the night before collection, you can place the end of a hose pipe in the hot tub, dropping it straight down into the water so that it lies on the bottom. Turn on the hose until water and no bubbles are coming from the end of the hose. Turn off the hose, disconnect it from the faucet, and take the end of the hose to the nearest drain allowing the water to pour by gravity. Or you can pull the plug inside the hot tub on the floor this will also slowly drain through the night. You can turn the power off but please keep the plug dry. I wouldn’t need anyone there if you do this, just access and can you please leave the tap adapter and chlorine tub outside.

Cold Weather Warning

  • Starting to fill the hot tub with the power off, wait till the hot water level is past the inlet/outlet pipes to turn back on, flick the switch on and press the reset button on the rcd, then you will need to press the power button on the control panel and make sure to press the heat activation button.
  • If outside temperature is below 10 degrees celsius, you will need to fill with hot water, depending on the shape of your kitchen tap I might have an adapter to fit.
  • Fill to the minimum level 6” of the top.
  • Keep the temperature set to 40 degrees celsius, it will balance between 38-40 degrees.
  • Please only use the hot tub for 30-60 minutes at a time, any longer will cause the temperature to drop below 35 degrees.
  • If the temperature drops below 35 degrees celsius, put the lid back on and make sure the heat button has been pressed.
  • Temperature can take 1-2 hours for every degree to heat up, depending on outside temperature.

Tap adapters I can supply, to fill with hot water

Hot Tub Rules (please read)

1. Do not leave non swimmers or children unattended.
2. Do not overload the spa.
3. Do not use extension leads unless supplied by me.
4. Do not drink alcohol during use of spa.
5. Please no glass or sharps in or around the spa.
6. If you are pregnant, have high blood pressure or cardiovascular conditions then consult your doctor before using the spa.

7. Do not allow water temperatures to exceed 40 degrees centigrade.
8. Its recommended that everyone shower before use.
9. No fake tan/bubble bath/confetti only water and chemicals inside the spa.
10. Do not stand on the filter housing.
11. No smoking/barbeques/fire pits to be used near the spa/gazebo.
12. Do not sit on the sides or dive into the spa.
13. It is your responsibility to look after the equipment hired to you so any problems please contact us immediately.
14. If you have used the equipment for the 1-3 days of hire then decide to tell us a problem you are not happy with you won’t be entitled to a refund.
15. If you damage the hot tub or gazebo you will be charged or will be settled in a small claims court so please be aware of that and have a good time.

Thank you for hiring

CONTROL PANEL

FILTER HOUSING

Signup for updates and offers